Scalable Approach for Power Droop Reduction During Scan-Based Logic BIST

The generation of significant power droop (PD) during at-speed test performed by Logic Built-In Self Test (LBIST) is a serious concern for modern ICs. In fact, the PD originated during test may delay signal transitions of the circuit under test (CUT): an effect that may be erroneously recognized as delay faults, with consequent erroneous generation of test fails and increase in yield loss. In this paper, we propose a novel scalable approach to reduce the PD during at-speed test of sequential circuits with scan-based LBIST using the launch-on-capture scheme. This is achieved by reducing the activity factor of the CUT, by proper modification of the test vectors generated by the LBIST of sequential ICs. Our scalable solution allows us to reduce PD to a value similar to that occurring during the CUT in field operation, without increasing the number of test vectors required to achieve a target fault coverage (FC). We present a hardware implementation of our approach that requires limited area overhead. Finally, we show that, compared with recent alternative solutions providing a similar PD reduction, our approach enables a significant reduction of the number of test vectors (by more than 50%), thus the test time, to achieve a target FC

Low-Cost and High-Reduction Approaches for Power Droop during Launch-On-Shift Scan-Based Logic BIST

During at-speed test of high performance sequential ICs using scan-based Logic BIST, the IC activity factor (AF) induced by the applied test vectors is significantly higher than that experienced during its in field operation. Consequently, power droop (PD) may take place during both shift and capture phases, which will slow down the circuit under test (CUT) signal transitions. At capture, this phenomenon is likely to be erroneously recognized as due to delay faults. As a result, a false test fail may be generated, with consequent increase in yield loss. In this paper, we propose two approaches to reduce the PD generated at capture during at-speed test of sequential circuits with scan-based Logic BIST using the Launch-On-Shift scheme. Both approaches increase the correlation between adjacent bits of the scan chains with respect to conventional scan-based LBIST. This way, the AF of the scan chains at capture is reduced. Consequently, the AF of the CUT at capture, thus the PD at capture, is also reduced compared to conventional scan-based LBIST. The former approach, hereinafter referred to as Low-Cost Approach (LCA), enables a 50% reduction in the worst case magnitude of PD during conventional logic BIST. It requires a small cost in terms of area overhead (of approximately 1.5% on average), and it does not increase the number of test vectors over the conventional scan-based LBIST to achieve the same Fault Coverage (FC). Moreover, compared to three recent alternative solutions, LCA features a comparable AF in the scan chains at capture, while requiring lower test time and area overhead. The second approach, hereinafter referred to as High-Reduction Approach (HRA), enables scalable PD reductions at capture of up to 87%, with limited additional costs in terms of area overhead and number of required test vectors for a given target FC, over our LCA approach. Particularly, compared to two of the three recent alternative solutions mentioned above, HRA enables a significantly lower AF in the scan chains during the application of test vectors, while requiring either a comparable area overhead or a significantly lower test time. Compared to the remaining alternative solutions mentioned above, HRA enables a similar AF in the scan chains at capture (approximately 90% lower than conventional scan-based LBIST), while requiring a significantly lower test time (approximately 4.87 times on average lower number of test vectors) and comparable area overhead (of approximately 1.9% on average)

Novel approach to reduce power droop during scan-based logic BIST

Significant peak power (PP), thus power droop (PD), during test is a serious concern for modern, complex ICs. In fact, the PD originated during the application of test vectors may produce a delay effect on the circuit under test signal transitions. This event may be erroneously recognized as presence of a delay fault, with consequent generation of an erroneous test fail, thus increasing yield loss. Several solutions have been proposed in the literature to reduce the PD during test of combinational ICs, while fewer approaches exist for sequential ICs. In this paper, we propose a novel approach to reduce peak power/power droop during test of sequential circuits with scan-based Logic BIST. In particular, our approach reduces the switching activity of the scan chains between following capture cycles. This is achieved by an original generation and arrangement of test vectors. The proposed approach presents a very low impact on fault coverage and test time, while requiring a very low cost in terms of area overhead. © 2013 IEEE

Power droop reduction during Launch-On-Shift scan-based logic BIST

The generation of significant power droop (PD) during at-speed test performed by Logic BIST is a concern for modern ICs. In fact, during test, PD may significantly increase the delay of signals of the circuit under test (CUT), an effect that may be erroneously recognized as presence of delay faults, with consequent erroneous generation of test fails, and increase in yield loss. In this paper, we propose a novel approach to reduce PD during at-speed test with scan-based Logic BIST using the Launch-On-Shift scheme. Our approach increases the correlation between adjacent bits of the scan chains with respect to conventional scan-based LBIST. This way, when the test vectors are applied, the activity factor (AF) of the scan chains is reduced by approximately the 50% with respect to conventional scan-based LBIST, with no drawbacks on test length and fault coverage, and at the cost of very limited area overhead. We also show that compared to two recent alternate solutions, our approach features a comparable AF in the scan chains during the application of test vectors, while it requires a significantly lower test time or area overhead

Low cost and low intrusive approach to test on-line the scheduler of high performance microprocessors

We propose a low cost and low intrusive approach to test on line the scheduler of high performance microprocessors. Differently from traditional approaches, it is based on looking for the information redundancy that the scheduler inherently has due to its performed functionality, rather than adding such a redundancy for on line test purposes. © 2010 author/owner(s)